Notice the rubber seal on the piston -- this is one of the components that is replaced when your transmission gets rebuilt. The next figure shows the alternating layers of clutch friction material and steel plates. The friction material is splined on the inside, where it locks to one of the gears. The steel plate is splined on the outside, where it locks to the clutch housing. These clutch plates are also replaced when the transmission is rebuilt. The pressure for the clutches is fed through passageways in the shafts.
The hydraulic system controls which clutches and bands are energized at any given moment. It may seem like a simple thing to lock the transmission and keep it from spinning, but there are actually some complex requirements for this mechanism.
First, you have to be able to disengage it when the car is on a hill the weight of the car is resting on the mechanism. Second, you have to be able to engage the mechanism even if the lever does not line up with the gear. Third, once engaged, something has to prevent the lever from popping up and disengaging. The parking-brake mechanism engages the teeth on the output to hold the car still. This is the section of the transmission that hooks up to the drive shaft -- so if this part can't spin, the car can't move.
Above you see the parking mechanism protruding into the housing where the gears are located. Notice that it has tapered sides. This helps to disengage the parking brake when you are parked on a hill -- the force from the weight of the car helps to push the parking mechanism out of place because of the angle of the taper. When the shift lever is placed in park, the rod pushes the spring against the small tapered bushing.
If the park mechanism is lined up so that it can drop into one of the notches in the output gear section, the tapered bushing will push the mechanism down. If the mechanism is lined up on one of the high spots on the output, then the spring will push on the tapered bushing, but the lever will not lock into place until the car rolls a little and the teeth line up properly.
This is why sometimes your car moves a little bit after you put it in park and release the brake pedal -- it has to roll a little for the teeth to line up to where the parking mechanism can drop into place. Once the car is safely in park, the bushing holds down the lever so that the car will not pop out of park if it is on a hill. The automatic transmission in your car has to do numerous tasks. You may not realize how many different ways it operates.
For instance, here are some of the features of an automatic transmission:. You've probably seen something that looks like this before.
It is really the brain of the automatic transmission, managing all of these functions and more. The passageways you can see route fluid to all the different components in the transmission.
Passageways molded into the metal are an efficient way to route fluid; without them, many hoses would be needed to connect the various parts of the transmission. First, we'll discuss the key components of the hydraulic system; then we'll see how they work together. The pump is usually located in the cover of the transmission. It draws fluid from a sump in the bottom of the transmission and feeds it to the hydraulic system. It also feeds the transmission cooler and the torque converter. The inner gear of the pump hooks up to the housing of the torque converter, so it spins at the same speed as the engine.
The outer gear is turned by the inner gear, and as the gears rotate, fluid is drawn up from the sump on one side of the crescent and forced out into the hydraulic system on the other side. The governor is a clever valve that tells the transmission how fast the car is going. It is connected to the output, so the faster the car moves, the faster the governor spins.
Inside the governor is a spring-loaded valve that opens in proportion to how fast the governor is spinning -- the faster the governor spins, the more the valve opens. Fluid from the pump is fed to the governor through the output shaft.
The faster the car goes, the more the governor valve opens and the higher the pressure of the fluid it lets through. To shift properly, the automatic transmission has to know how hard the engine is working. There are two different ways that this is done. Some cars have a simple cable linkage connected to a throttle valve in the transmission. The further the gas pedal is pressed, the more pressure is put on the throttle valve. Other cars use a vacuum modulator to apply pressure to the throttle valve.
The modulator senses the manifold pressure, which increases when the engine is under a greater load. The manual valve is what the shift lever hooks up to.
Depending on which gear is selected, the manual valve feeds hydraulic circuits that inhibit certain gears. For instance, if the shift lever is in third gear, it feeds a circuit that prevents overdrive from engaging. Shift valves supply hydraulic pressure to the clutches and bands to engage each gear. The valve body of the transmission contains several shift valves.
The shift valve determines when to shift from one gear to the next. For instance, the 1 to 2 shift valve determines when to shift from first to second gear. The shift valve is pressurized with fluid from the governor on one side, and the throttle valve on the other.
They are supplied with fluid by the pump, and they route that fluid to one of two circuits to control which gear the car runs in. The shift valve will delay a shift if the car is accelerating quickly.
If the car accelerates gently, the shift will occur at a lower speed. Let's discuss what happens when the car accelerates gently. As car speed increases, the pressure from the governor builds. This forces the shift valve over until the first gear circuit is closed, and the second gear circuit opens.
Since the car is accelerating at light throttle, the throttle valve does not apply much pressure against the shift valve. When the car accelerates quickly, the throttle valve applies more pressure against the shift valve.
This means that the pressure from the governor has to be higher and therefore the vehicle speed has to be faster before the shift valve moves over far enough to engage second gear. Each shift valve responds to a particular pressure range; so when the car is going faster, the 2-to-3 shift valve will take over, because the pressure from the governor is high enough to trigger that valve. Electronically controlled transmissions, which appear on some newer cars, still use hydraulics to actuate the clutches and bands, but each hydraulic circuit is controlled by an electric solenoid.
This simplifies the plumbing on the transmission and allows for more advanced control schemes. In the last section we saw some of the control strategies that mechanically controlled transmissions use. Electronically controlled transmissions have even more elaborate control schemes. In addition to monitoring vehicle speed and throttle position, the transmission controller can monitor the engine speed, if the brake pedal is being pressed, and even the anti-lock braking system.
Using this information and an advanced control strategy based on fuzzy logic -- a method of programming control systems using human-type reasoning -- electronically controlled transmissions can do things like:. Let's talk about that last feature -- inhibiting the upshift when going into a turn on a winding road. Let's say you're driving on an uphill, winding mountain road.
When you are driving on the straight sections of the road, the transmission shifts into second gear to give you enough acceleration and hill-climbing power. When you come to a curve you slow down, taking your foot off the gas pedal and possibly applying the brake. Most transmissions will upshift to third gear, or even overdrive, when you take your foot off the gas. Then when you accelerate out of the curve, they will downshift again.
But if you were driving a manual transmission car, you would probably leave the car in the same gear the whole time. Some automatic transmissions with advanced control systems can detect this situation after you have gone around a couple of the curves, and "learn" not to upshift again. For more information on automatic transmissions and related topics, check out the links on the next page. Sign up for our Newsletter!
Mobile Newsletter banner close. Mobile Newsletter chat close. Buyer's Guide. Type keyword s to search. Today's Top Stories.
Subaru Forester Wilderness Conquers the Outback. A Heretic in the Corvette Chapel. Future Cars Worth Waiting For: — Operation of an Automatic Transmission The most common type of automatic transmission uses hydraulic power to shift gears. Gears of an Automatic Transmission The gears of an automatic transmission include the following: According to How a Car Works , when you shift your vehicle into drive, you engage all available forward gear ratios.
This means that the transmission can move between its full range of gears as needed. Six-speed automatic transmissions are the most common number of gears, but older cars and entry-level compact cars may still have either four or five automatic gears. Third gear either locks the transmission in third gear or limits it to the first, second, and third gear ratios.
This provides the power and traction needed to go either uphill or downhill or to tow a boat, RV, or trailer. When the engine reaches a designated level of revolutions per minute RPM , most vehicles automatically drop third gear to keep the engine from harm. Second gear either locks the transmission in second gear or limits it to the first and second gear ratios.
This gear is ideal for going uphill and downhill in slippery conditions as well as driving during ice, snow, and other types of inclement weather.
First gear is used when you want to lock the transmission in first gear, although some vehicles will automatically switch out of this gear to protect the engine at a certain RPM. Like second and third gear, this gear is best used for towing, driving uphill or downhill, and when traveling during slippery, icy conditions.
Advantages of an Automatic Transmission According to How Stuff Works , the biggest advantage of an automatic transmission is the ability to drive without the need for a clutch as is required with a manual transmission. You may be able to find more information about this and similar content at piano.
Another big reason cars need a gearbox is torque. Torque is basically a rotational force. In the case of lug nuts on a tire you have to apply a lot of torque to get them moving, cars also need a lot of torque at first to get started.
So since first gear is 3. The cool thing about electric motors is that they have their maximum torque at zero RPM and that max torque stays until about RPMs. So we have two questions that we really need to answer in order to discuss whether or not electric cars in the future could be using manual transmissions. First of all, is it possible? And second of all, is it logical? The first question is it possible?
Of course, you have to have the controllers in the battery but it could be done. The other question, is it logical?
0コメント